This guide is for an office of roughly fifty to five hundred people: one building or a few floors, a phone on many desks, Wi-Fi everywhere, maybe a few cameras, and an internet edge to protect. It walks through the four parts of that network (access switches, the layer that ties them together, the firewall, and the access points) and names the Juniper and Ruckus gear we sell for each, with the maker's own figures.
Start with what plugs in
Before choosing a switch, count three things per floor or wiring closet: wired drops, devices that take power from the switch (phones, access points, cameras), and the uplinks back to the core. The powered devices decide more than the port count does. Juniper's Power over Ethernet overview explains why: "The PoE IEEE standards define classes for devices based on the levels of power they require", and the switch allocates power by class. Two of the PoE versions Juniper lists:
| Standard | Power at the switch port | Juniper's description |
|---|---|---|
| IEEE 802.3af (PoE) | up to 15.4 W | "supplied up to 15.4 W of power to a connected powered device" |
| IEEE 802.3at (PoE+) | up to 30 W | "Supplies up to 30 W of power." |
The device receives less than the port sends. Juniper's class table puts class 4 at "30.0 W" at the port and "12.95 through 25.5 W" at the device, and says line loss "is typically less than 16 percent of the maximum power." Add up the class of every powered device in a closet; that total has to fit inside the switch's PoE budget.
Access switches
Juniper EX3400. Per Juniper's EX3400 system overview, the switch comes "With 24 or 48 RJ-45 ports", and "Models that support PoE or PoE+ provide that support on all RJ-45 ports." The PoE budget depends on the power supplies:
| Model | PoE budget, one power supply | PoE budget, two power supplies |
|---|---|---|
| EX3400-24P | 370 W with one 600 W power supply installed | 720 W with two 600 W power supplies installed |
| EX3400-48P | 740 W with one 920 W power supply installed | 1440 W with two 920 W power supplies installed |
For uplinks it has "Four uplink ports (labeled 0 through 3 on the front panel)" for SFP and SFP+ optics, "and two 40-Gigabit Ethernet ports" on the rear. Several closets can run as one switch: "you can connect up to 10 EX3400 switches together to form one unit that you manage as a single chassis, called a Virtual Chassis". By default "The QSFP+ uplink ports are configured as Virtual Chassis ports (VCPs)". One planning note: Juniper has announced the EX3400's end of life, with a last order date of 04/30/2027 and end of support on 04/30/2032, per its EX Series end of life page.
Juniper EX2300. For a small office or a small closet, the EX2300 is the smaller sibling: "12 (in EX2300-C switches), 16, 24, 32, or 48 built-in Gigabit Ethernet RJ-45 network ports", and "you can connect up to four EX2300 switches in a Virtual Chassis configuration". Its "Uplink ports do not support PoE." Juniper's end of life page lists an end of support date of 09/30/2031 for it.
Ruckus ICX 7250 and ICX 7450. Ruckus describes both for "enterprise Gigabit Ethernet (GbE) access deployment". The ICX 7250 "raises the bar with up to 8×10 GbE ports for uplinks or stacking". The ICX 7450 "delivers market-leading stacking density with up to 12 switches (576 1 GbE and 48 10 GbE ports) per stack" and was, in Ruckus's words, "the first in its class to offer 40 GbE uplinks". These descriptions are from the product list on Ruckus's support site.
Tying the closets together
In a smaller office, one stack or Virtual Chassis is the whole switching layer: the access switches uplink to each other and the firewall. As the office grows to several closets, an aggregation layer collects their uplinks. On the Ruckus side, the ICX 7750 is described as an "aggregation and core distributed chassis switch offering for enterprise LANs" that "supports 12-unit distributed chassis stacking or Multi-Chassis Trunking (MCT)", and the ICX 7850 as "a high performance stackable core switch for next generation 100G campus". Either way, size the uplinks from each closet first, then the aggregation ports.
The firewall
Juniper SRX345. The SRX345 "consolidates security, routing, switching, and WAN interfaces for midsize distributed enterprises". It has "eight 1 G Ethernet ports, eight 1 G SFP ports, one management port", and Juniper says it "supports up to 5-Gbps firewall and 800-Mbps IPsec VPN, and is suited for midsize to large distributed enterprise branch office deployments."
Juniper SRX1500. For the larger end of this range, the SRX1500 is a "mid-range dynamic services gateway" for "small to medium enterprises", with "twelve 1G Ethernet ports, four 1G SFP ports, and four 10G SFP+ ports". Juniper says it "supports up to 9-Gbps of firewall throughput and is suited for enterprise campus and data center edge deployments."
Pick on the internet circuit you have and the inspection features you will turn on, not on the headline number alone.
Wi-Fi
Access points draw from the same PoE budget as phones and cameras. Find the class your access point model presents in its maker's data sheet, then add it to the closet's PoE total from the table above. A class 4 device, for example, takes "30.0 W" from the port. Run each access point to the closest closet, and leave room in the PoE budget for the ones you will add later.
In stock at Townsend
For access switches we have the Juniper EX3400-48P and the Ruckus ICX 7250 in stock, for the firewall the Juniper SRX345, and Ruckus access points for Wi-Fi. The full ranges are on the EX3400, ICX, SRX345 and Ruckus access point shelves.
The answer is the arithmetic above: class times count, per closet, against the budget. When you ask for a quote, send the device counts per closet and we will match switches to them.




