Juniper describes the EX4600 as a second generation switch for campus networks, used as a campus distribution switch, a small campus core, or a top-of-rack switch in small data centers. It is one 1 U switch, sold as the EX4600-40F in several versions, with 24 SFP+ ports, 4 QSFP+ uplinks and two bays for expansion modules. This guide covers the versions, the two expansion modules, Virtual Chassis with the EX4300, power, and the end of life dates Juniper has now set, all from Juniper's EX4600 Switch Hardware Guide and end of life page.
The short answer
Buy an EX4600 to aggregate 10GbE links in a campus or a small data center: the fixed ports give up to 40 logical 10GbE ports, and with two QFX-EM-4Q modules the switch reaches 72 10GbE interfaces in 1 U. It also fits beside EX4300 access switches, because the two can share one Virtual Chassis with the EX4600 in charge. Pick the version by airflow and power feed, and buy the expansion modules and any spares now, for the reason given under end of life below.
The versions
| Part number | Ports | Expansion bays | Power | Airflow |
|---|---|---|---|---|
| EX4600-40F-AFO | 24 SFP+, 4 QSFP+ | 2 | AC | Air Out (port-to-FRU) |
| EX4600-40F-AFI | 24 SFP+, 4 QSFP+ | 2 | AC | Air In (FRU-to-port) |
| EX4600-40F-DC-AFI | 24 SFP+, 4 QSFP+ | 2 | DC | Air In (FRU-to-port) |
| EX4600-40F-S | 24 SFP+, 4 QSFP+ | 2 | Bought separately | Set by the fans and supplies fitted |
Every version except the EX4600-40F-S ships with two power supplies and five fans; the -S ships without them. The chassis is 1.72 in. high, 17.36 in. wide and 20.48 in. deep, and weighs 21.7 lbs with power supplies and fan modules installed. The 24 fixed ports, numbered 0 through 23, take 10 Gbps SFP+ transceivers.
Expansion modules: QFX-EM-4Q and EX4600-EM-8F
The two bays take either module, and expansion modules are sold separately from the switch. The QFX-EM-4Q adds four QSFP+ ports, so two of them bring the switch to 72 interfaces counted as 10GbE. The EX4600-EM-8F adds eight SFP+ ports, and two of them bring the switch to 56 interfaces. Choose the QFX-EM-4Q for more 40 Gbps uplinks or more 10GbE through breakout cables, and the EX4600-EM-8F for more native SFP+ ports.
Buffers, power and cooling
The EX4600 has 12 MB of shared buffer, of which 25 percent is dedicated and the rest shared among all ports, which helps it absorb bursts at a distribution layer. Juniper puts each 10GbE port at under five watts, and gives the AC-powered switch a typical draw of 230 W and a maximum of 365 W. The AC cords use a C13 coupler to IEC standard 60320. The switch can run on one power supply, and with two installed the second carries the load without interruption if the first fails or is removed. The power supplies, fan modules, optics and expansion modules are all hot-swappable field-replaceable units. The control plane runs on a 1.5 GHz dual-core Intel CPU with 32 GB of SSD storage.
Virtual Chassis with EX4600 and EX4300 switches
An EX4600 Virtual Chassis joins up to 10 switches in a ring and manages them as one. The EX4600 can also share a Virtual Chassis with EX4300 switches, where the EX4600 can be primary, backup or line card and the EX4300 switches must be line cards. Juniper fully supports the EX4600 as primary in a mixed Virtual Chassis from Junos OS Release 14.1X53-D25, and every EX4600 runs Junos OS Release 13.2X51-D25 or later. That makes the EX4600 the natural aggregation switch for a closet or a building already standardized on the EX4300.
End of life: last order 12/29/2026
Juniper announced the end of life of the EX4600 in bulletin TSB109286, and the notice covers every EX4600-40F version and both expansion modules, the EX4600-EM-8F and the QFX-EM-4Q.
| EOL Announced | Last Order | End of Hardware Failure Analysis | End of Engineering | Last Software Version | End of Support |
|---|---|---|---|---|---|
| 06/29/2026 | 12/29/2026 | 12/29/2027 | 12/29/2029 | 21.4 | 12/29/2031 |
The last order date is still ahead, but it is close: after it, Juniper takes no new orders for the switch or its modules. Support runs until 12/29/2031, with 21.4 as the last software version, so an EX4600 bought now still has years of supported service. If a design depends on the QFX-EM-4Q or EX4600-EM-8F, buy the modules and a spare switch while they are still easy to find.
In stock at Townsend
Searches that show Townsend for the EX4600 are led by the switch itself, the EX4600-40F-AFO and the EX4600-EM-8F module, alongside owners looking to sell their EX4600 switches. In stock now: the EX4600-40F-AFI, the EX4600-40F-AFO and the EX4600-EM-8F expansion module.
Where to look
The EX4600 page lists every EX4600 and module in stock, the EX Series page the rest of the line, and Juniper transceivers the SFP+ and QSFP+ optics. For the end of life notice on its own, read Juniper EX4600 end of life; for the other EX lines, read Juniper's newer EX switches compared. Request a quote for a configuration that is not listed, or sell the switches you retire.




