Juniper's QFX5100 is a line of 10GbE and 40GbE data center switches, made as top-of-rack and spine switches for Layer 2 and Layer 3 fabrics, in 24, 48 and 96 port configurations. This guide sets the QFX5100-48S, QFX5100-48T, QFX5100-24Q and QFX5100-96S side by side from Juniper's QFX5100 Switch Hardware Guide, explains the part number suffixes, and gives the support dates from Juniper's end of life page, which matter more for this line than for most.
The short answer
For 10GbE fiber or direct attach to servers, the QFX5100-48S has 48 SFP+ ports and 6 QSFP+ ports; the QFX5100-96S doubles that to 96 SFP+ and 8 QSFP+ in 2 U. For 10GBASE-T copper, the QFX5100-48T has 48 10GBASE-T ports and 6 QSFP+ ports. For a 40GbE spine, the QFX5100-24Q has 24 QSFP+ ports, each usable as one 40 Gbps port or four 10 Gbps ports. Juniper's own advice for a Virtual Chassis Fabric is to use the QFX5100-24Q as the spine wherever possible.
The models side by side
| Model | Ports | Full duplex throughput | Height | Weight with FRUs |
|---|---|---|---|---|
| QFX5100-48S | 48 x SFP+, 6 x QSFP+ | 1.44 Tbps | 1 U | 21.8 lbs (9.8 kg) |
| QFX5100-48T | 48 x 10GBASE-T, 6 x QSFP+ | 720 Gbps | 1 U | 24.79 lbs (11.2 kg) |
| QFX5100-24Q | 24 x QSFP+, plus 2 expansion bays | 2.56 Tbps | 1 U | 22 lbs (9.97 kg) |
| QFX5100-96S | 96 x SFP+, 8 x QSFP+ | Not stated in the guide | 2 U | 32 lbs (14.5 kg) |
The SFP+ ports run at 10 Gbps with 10 Gbps optics and also at 1 Gbps or 100 Mbps with gigabit optics. Every model shares the same control plane: a 1.5 GHz dual-core Intel CPU with 8 GB of memory and 32 GB of SSD storage. The QFX5100-48TH looks like a QFX5100-48T but ships with Satellite Network Operational System instead of Junos OS and can only be used as a satellite device in a Junos Fusion system, so check for the H before you buy one as a standalone switch.
Expansion modules for the QFX5100-24Q
The QFX5100-24Q has two module bays for the QFX-EM-4Q, which together add 8 more QSFP+ ports, and the bays also take the EX4600-EM-8F, which adds 8 SFP+ ports. Any mix of the two is supported and both are hot-swappable, but putting an EX4600-EM-8F where a QFX-EM-4Q was takes the interfaces down for a moment while the configuration changes.
What the part number suffixes mean
Every QFX5100 comes with AC or DC power and with airflow-in or airflow-out cooling; on older switches with an LCD the same choice is called front-to-back and back-to-front. In Juniper's product number table, AFO models are listed as Air Out and AFI models as Air In, so the QFX5100-48T-AFI is an Air In switch, and DC models carry DC in the part number. The 3 in a part number such as the QFX5100-48S-3AFO is the number of management ports in that table: 3 against 2 on the QFX5100-48S-AFO.
Power and cooling
A QFX5100 runs on one or two power supplies; with two, if one fails or is pulled, the other carries the load without interruption. The 1 U models have five fan modules and the 2 U QFX5100-96S has three. The AC cords use a C13 coupler to IEC standard 60320.
| Model (AC power) | Typical power consumption | Maximum power consumption |
|---|---|---|
| QFX5100-24Q | 230 W | 365 W |
| QFX5100-48S | 230 W | 365 W |
| QFX5100-48T | 322 W | 395 W |
| QFX5100-96S | 315 W | 470 W |
Virtual Chassis and Virtual Chassis Fabric
A QFX Virtual Chassis joins up to 10 QFX3500, QFX3600 or QFX5100 switches into one logical device in a ring. A Virtual Chassis Fabric goes further: up to 20 devices in a spine and leaf layout, at most 4 of them spines, with QFX3500, QFX3600 and EX4300 switches allowed as leaves. That makes the QFX5100 a practical way to extend an existing QFX5100 fabric or to add leaves under QFX5100 spines without changing the design.
End of life: the dates that decide a QFX5100 purchase
Juniper's QFX end of life page lists the QFX5100-48S, QFX5100-24Q and QFX5100-48T part numbers in one notice and the QFX5100-96S in another.
| Models | EOL Announced | Last Order | End of Support |
|---|---|---|---|
| QFX5100-48S, QFX5100-24Q, QFX5100-48T | 04/30/2021 | 07/01/2022 | 07/01/2027 |
| QFX5100-96S | 05/25/2022 | 12/31/2022 | 12/31/2027 |
Juniper support for most of the line ends in 2027, so buy a QFX5100 to match or extend a fabric you already run, or for a lab, and plan new builds around a current line. The fan modules and power supplies are field-replaceable and hot-swappable, so spares on the shelf are what keep an installed QFX5100 running once Juniper support ends.
In stock at Townsend
In stock now: the QFX5100-48S-3AFO, the QFX5100-48S-AFI, the QFX5100-96S-AFO and the QFX5100-96S-AFI, with spare fan modules and QFX-EM-4Q expansion modules.
Where to look
The QFX5100 page lists every QFX5100 in stock, the QFX Series page the rest of the line, and Juniper transceivers the SFP+ and QSFP+ optics. For the end of support notice on its own, read Juniper QFX5100 end of support; for the lines that followed, read Juniper's other QFX switches compared. Request a quote for a configuration that is not listed, or sell the switches you retire.




